Accueil
poe
Passive PoE Injector Cable Set : ID 435 : $5.95 : Adafruit Industries, Unique & fun DIY electronics and kits

Passive PoE Injector Cable Set : ID 435 : $5.95 : Adafruit Industries, Unique & fun DIY electronics and kits

4.7 (352) · € 3.00 · En Stock

Adafruit Industries, Unique & fun DIY electronics and kits Passive PoE Injector Cable Set : ID 435 - Simplify your Internet of Things with a passive PoE injector cable. These are quite handy for projects that have Ethernet connectivity and also need a power cable. Of course, you can get a long Ethernet cable but then you have to figure out how to plug it in, making a
Simplify your Internet of Things with a passive PoE injector cable. These are quite handy for projects that have Ethernet connectivity and also need a power cable. Of course, you can get a long Ethernet cable but then you have to figure out how to plug it in, making a mess of wires. There is an official Power-over-Ethernet standard that allows devices and routers to activate a 48VDC power line on the unused Ethernet pins (4,5 and 7,8) but PoE is expensive, requiring a special router and then a step-down converter to handle the high 48V lineFor DIY projects, you may want to consider using these cables instead. One cable (the injector half) has a Ethernet plug and port and a 2.1mm jack. When you plug in a power supply (say a 9VDC wall adapter), the injector merges the power adapter in so that pins 4 and 5 connect to the power adapter power and pins 7 and 8 have the ground signal. This is also known as "Mode B" compatibility The other cable (the extractor half) does the opposite, splitting off pins 4,5 and 7,8 and bringing them to a 2.1mm DC barrel plug. You can then use the DC plug to power your projects as if it was connected directly to the wall adapter.These are NOT official/standard "Power Over Ethernet" cables and you cannot use these to provide power to an Arduino or other products from an official PoE host device (which will supply 48VDC). They must be used a pair!Note that Ethernet cables, especially long ones, will act like resistors as you get past 10 meter spans. Most Ethernet cables are 24AWG, 0.085 ohms per meter (0.026 ohms per foot) so if you want to draw say 500mA from your adapter, there will be a 1 Volt drop for every ~25 meters / 80 feet.Because these cables use pins 4,5,7, and 8 to pass power you can't use these in gigabit Ethernet situations (those pins would be used by the gigabit router), but your device and router should back down to 10/100 megabit in such cases.

Passive POE Injector Kit - BC Robotics

adafruit-PoE Splitter with USB Type C - 5V 2A - 100 MB Ethernet

Power over Ethernet (PoE) can make your project wiring a breeze - instead of needing a wire for power and data, you can use one Ethernet cable for

5V 1.5A Output PoE Module - Works with Raspberry Pi 3 B+ or Pi 4

PoE injector and splitter kit with 5.5mm x 2.1 mm Dc jack / plug Allows use of any DC voltage up to 60V, Only support 10@Mbps network. Transforms Non

5 Pairs Passive PoE Injector and PoE Splitter Kit with 5.5x2.1 mm DC Connector RJ45 Power Over Ethernet

PoE injector and splitter kit with 5.5mm x 2.1 mm DC jack / plug Allows use of any DC voltage up to 57V Only support 10@Mbps network. Transforms Non PoE devices to PoE enabled Use with IP security camera, wireless access point and other devices Note: This kit need the external power adapter to power on the device. br / Passive PoE Injector and PoE Splitter Kit allows low cost of delivering power over the network cable for shorter distances.

iCreatin Passive PoE Injector and PoE Splitter Kit with 5.5x2.1 mm DC Connector

In-line wire 1-to-4 splitter : ID 402 : $1.95 : Adafruit Industries, Unique & fun DIY electronics and kits

Redundant Power Sources for Electronics? - Electrical - Chief Delphi

Wireless is wonderful, but sometimes you want the strong reliability of a wire. If your Feather board is going to be part of a permanent installation,

Adafruit Ethernet FeatherWing

Passive PoE Injector Cable Set : ID 435 : $5.95 : Adafruit Industries, Unique & fun DIY electronics and kits

iCreatin Passive PoE Injector and PoE Splitter Cable Kit with 2.1x 5.5mm DC Barrel Jack (5-Pack) : Electronics

UCTRONICS USB-C PoE Splitter Gigabit, PoE to USB-C 5V/4A Power Supply for Raspberry Pi 4 and More, 802.3at Power Over Ethernet to USB Type-C Adapter : Electronics

POE Texas

Wireless is wonderful, but sometimes you want the strong reliability of a wire. If your Feather board is going to be part of a permanent installation, this Ethernet FeatherWing will let you add quick and easy wired Internet. Just plug in a standard ethernet cable, and run the Ethernet2 library for cross-platform networking. Works with all/any of our Feather boards as an Ethernet Client (server not supported at this time)! Ethernet is a tried-and-true networking standard.

Adafruit Ethernet FeatherWing ADA3201

Power over Ethernet (PoE) splitters can make your project wiring a breeze - and best of all they work to connect any 802.3af-capable router to any Ethernet device, even if it doesn't natively support PoE! The splitter takes a unified PoE signal (data and power) from one RJ-45 cable, and then separates the data (Ethernet) and power (5 VDC regulated) into two different lines for non-PoE devices.